Bunn G2 Anleitung zur Fehlerbehebung PDF herunterladen

G1, G2 & G3 GRINDERS

USE & CARE INSTRUCTIONS

STEP 1 STEP 2 STEP 3 STEP 4

Raise the top lid and add the whole

bean coffee. Close the top lid.

Allow the bag to rest on the screen

beneath the chute.

Turn the selector knob to align the

red arrow with the desired grind.

STEP 5

Turn the ON/OFF switch to ON and

press the start switch.

STEP 6 STEP 7

STEP 8

39565 102506

Locate the back of a bag behind

the dispense chute. (The grinder

will not operate unless the bag is

behind the chute.) This will activate

the bag switch.

Flip the cleaning lever a few times

as dispensing slows.

Remove the bag when ground cof-

fee is no longer dispensed from

the chute. The grinder will stop

automatically when the bag is

removed.

NOTE - The start switch will have

to be pressed again to continue the

cycle if the bag is removed before

grinding is completed. Turn the

ON/OFF/START switch to the OFF

position.

COFFEE GRINDING

STEP 2

STEP 3

WARNING - Prior to cleaning the

grind chamber, unplug the grinder

before removal of any panel or grind

chamber housing parts.

Empty all beans from hopper(s).

Plug in the grinder and place an

empty bag behind the dispense

chute. Press and release the

“START” switch. Run a few cycles

until all coffee in the grind chamber

is dispensed and disconnect the

grinder from the power source.

Remove the bag.

STEP 1

Clean all exterior surfaces using

a damp cloth rinsed in any mild,

nonabrasive, liquid detergent. Care

should be taken not to scratch the

grinder with any abrasive material.

STEP 5

Remove the two screws securing

the stationary burr to the grind

chamber.

STEP 4

STEP 6

Remove the two screws and remove

the dial plate and selector knob

assembly.

Slide the burr auger rotor/spring

assembly off the motor shaft and

disassemble for cleaning.

CLEANING

STEP 9

Align the slot in the motor shaft with

the rotor and reinstall shear plate.

Reinstall rotor cup and grind selec-

tor dial plate to the burr housing.

Refer to the Operating and Service

manual for burr adjustments.

STEP 8

Carefully clean the grind chamber,

dial plate assembly, chute open-

ing and dial plate opening with a

dry stiff non metallic bristle brush.

Wipe with a clean cloth that has

been soaking in a mild solution of

detergent and hot water. Reinstall

the spring and rotor with burr onto

the motor shaft.

STEP 7

Wash all parts in a mild solution of

detergent with hot water and a stiff

non metallic bristle brush. Rinse all

parts thoroughly and allow them to

air dry before reinstalling.

1 2

G1, G2 & G3 GRINDERS 1

Inhaltsverzeichnis

Seite 1 - G1, G2 & G3 GRINDERS

G1, G2 & G3 GRINDERSUSE & CARE INSTRUCTIONSSTEP 1 STEP 2 STEP 3 STEP 4Raise the top lid and add the whole bean coffee. Close the top lid.Allow

Seite 2

39565 102506G1, G2 & G3 GRINDERSTROUBLESHOOTINGA troubleshooting guide is provided to suggest probable causes and remedies for the most likely pro

Weitere Dokumente für Geradeschleifer Bunn G2

Um das Dokument anzuzeigen Bunn G2 Wartungshandbuch

Bunn G2 Wartungshandbuch (21 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Bunn G2 Anleitung zur Fehlerbehebung

Stöbern Sie online oder laden Sie Anleitung zur Fehlerbehebung nach Geradeschleifer Bunn G2 herunter. Bunn G2 Troubleshooting guide Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Geradeschleifer Bunn G2

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Geradeschleifer Bunn G2