Bunn FCD-4 Bedienungsanleitung

BUNN-O-MATIC CORPORATIONPOST OFFICE BOX 3227SPRINGFIELD, ILLINOIS 62708-3227PHONE: (217) 529-6601 FAX: (217) 529-664433496.0000C 08/01 ©2000 Bu

10DISPENSER USEPress and Hold Models (Refer to Fig 5)1. Place a cup on the drip tray beneath the desired dispensing nozzle.2. Press and hold the “Prod

11CLEANING & PREVENTIVE MAINTENANCEGeneral Cleaning and Sanitizing ProceduresNote: The Bunn Juice Dispenser incorporates a rinse reminder feature

12CLEANING (cont)portion contol dispensers. The “REFILL” indicator will light and the beeper will sound for the dispense headselected.7. Once the disp

13Monthly: Clean Condenser Air Filter1. Remove the condenser air filter located on the rear of the dispenser.2. Using a water spray, clean the air fil

14ADJUSTMENT & OPTIONAL SETTINGSSETTING THE MIX RATIO/BRIXRatio Cup Method1. Adjust the water flow as described in Water Flow Testing and Adjustme

15Water Flow Testing and Adjustment1. Enter the “Pump Speed Programming” mode by simultaneously press-ing both “Hidden Switches” Fig 5 or Fig 6. Note

16that each step is confirmed by a single flash of the appropriate “REFILL” indicator and a single tone from thebeeper.4. Repeat as necessary at the r

17b) In a 5 second period, press and release the “Chilled Water Switch” the number of times that you want thepassword set to (maximum of 10.) For exam

18Password ProtectionThe programming modes and service lockout function may be password protected to prevent accidental orunauthorized access to t

19Dispense Fault List“REFILL” indicator Beeper Fault2 flashes 2 beeps Dispense station locked out.3 flashes 3 beeps DISPENSE/RINSE sensing fault.4 fla

2WARRANTYBunn-O-Matic Corp. (“Bunn”) warrants the equipment manufactured by it to be commercially free from defectsin material and workmanship existin

20Dip Switch Function ListDip Switch Controls Off On1 “REFILL” indicator when “concentrate out” is detected. Inactive Active2 Lockout dispense compone

21COOLANT SCHEMATIC DIAGRAMCONDENSERSUCTIONACCUMULATORCOMPRESSOREVAPORATORPROCESS TUBE33464.0000A 09/00 ©2000 Bunn-O-Matic CorporationFILTERDRYE

22J3-1J3-2J1-1J1-5J1-10 CONTROL P C BOARDJ1-18J7-1J7-5J7-10J7-16J8-1J8-8J6-1J6-6J6-12RIGHTLAMP ASSY. LEFT LAMPASSY. GRNGRNGRNNL1BLUBRN/BLKRED/BLKRED/B

3USER NOTICESCarefully read and follow all notices on the equipment and in this manual. They were written for your protec-tion. All notices are to be

4INITIAL SET-UPCAUTION: The dispenser is very heavy! Use care when lifting or moving it. Use at least two people to lift ormove the dispenser. Place t

5PLUMBING REQUIREMENTSThis dispenser must be connected to a COLD WATER system with operating pressure between 20 and 100psi (138 and 690 kPa). This wa

6OPERATING CONTROLSRefrigeration SwitchThe refrigeration switch is located on the top of the dispenser nearthe left rear corner. This switch controls

7OPERATING CONTROLS (cont.)FIG 5 Press and Hold ModelsA. Product Dispense SwitchPressing and holding switch will initiate product flow from the resp

8INITIAL FILLCAUTION: The dispenser must be disconnected from the power source throughout the initial fill except whenspecified in the instructions.1.

9INITIAL FILL (cont)Ambient Concentrates (Optional)1. Install an Ambient Concentrate Conversion Kit (BUNN-O-MATIC part number 33699.0000) per the inst